Validation Report: renesas-ck_ra6m5

Superseded. This is the auto-generated report for the staged onboarding/renesas-ck_ra6m5 descriptor (a generic UART fixture on a placeholder memory map: its code flash at 0x0800_0000 is the RA6M5 data-flash address, not the 2 MiB code flash at 0x0). The promoted RA6M5 part is r7fa6m5bh, and the board package is EK-RA6M5. The staged descriptor stays only because crates/core/src/bus/known_stubs.rs still cites it.

Architecture: ARM Cortex-M33.

1. Dynamic Simulation Validation

Status: ✅ Passed (simulation-ok)

[2m2026-10-18T14:40:20.311205Z[0m [32m INFO[0m [2mlabwired_cli::commands::run[0m[2m:[0m Starting LabWired Simulator
[2m2026-10-18T14:40:20.317562Z[0m [32m INFO[0m [2mlabwired_core::system::builder[0m[2m:[0m Loading chip descriptor: ../../chips/onboarding/renesas-ck_ra6m5.yaml
[2m2026-10-18T14:40:20.323773Z[0m [33m WARN[0m [2mlabwired_core::bus::profiles[0m[2m:[0m GPIO type 'renesasra_gpiomisc' (peripheral 'portMisc') has no dedicated register model; falling back to the STM32F1 placeholder layout. This is a known-incomplete onboarding model — set `config.profile` or add a real model for correct behaviour.
[2m2026-10-18T14:40:20.323943Z[0m [32m INFO[0m [2mlabwired_cli::commands::run[0m[2m:[0m Loading firmware: "/home/andrii/Projects/labwired-renode/core/tests/fixtures/uart-ok-thumbv7m.elf"
[2m2026-10-18T14:40:20.324035Z[0m [32m INFO[0m [2mlabwired_loader[0m[2m:[0m ELF Entry Point: 0x401
[2m2026-10-18T14:40:20.324045Z[0m [32m INFO[0m [2mlabwired_cli::commands::run[0m[2m:[0m Firmware Loaded Successfully!
[2m2026-10-18T14:40:20.324049Z[0m [32m INFO[0m [2mlabwired_cli::commands::run[0m[2m:[0m Entry Point: 0x401
[2m2026-10-18T14:40:20.325335Z[0m [32m INFO[0m [2mlabwired_cli::commands::run[0m[2m:[0m Starting Simulation (ARM Cortex-M)...
[2m2026-10-18T14:40:20.325345Z[0m [32m INFO[0m [2mlabwired_cli::commands::run[0m[2m:[0m Initial PC: 0x400, SP: 0x20020000
[2m2026-10-18T14:40:20.325351Z[0m [32m INFO[0m [2mlabwired_cli[0m[2m:[0m Running for 20000 steps...
[2m2026-10-18T14:40:20.335105Z[0m [32m INFO[0m [2mlabwired_cli[0m[2m:[0m Progress: 10000 steps, current IPS: 905134.81
[2m2026-10-18T14:40:20.348470Z[0m [32m INFO[0m [2mlabwired_cli::report[0m[2m:[0m Simulation loop finished.
[2m2026-10-18T14:40:20.348563Z[0m [32m INFO[0m [2mlabwired_cli::report[0m[2m:[0m Final PC: 0x466
[2m2026-10-18T14:40:20.348596Z[0m [32m INFO[0m [2mlabwired_cli::report[0m[2m:[0m Total Instructions: 19999
[2m2026-10-18T14:40:20.348624Z[0m [32m INFO[0m [2mlabwired_cli::report[0m[2m:[0m Total Cycles: 20002
[2m2026-10-18T14:40:20.348650Z[0m [32m INFO[0m [2mlabwired_cli::report[0m[2m:[0m Average IPS: 813076.68

Hardware Coverage Report

Peripheral ID	Base Address	Type
`led_red`	`0x0000000a`	`led`
`led_green`	`0x00000009`	`led`
`led_blue`	`0x00000001`	`led`
`button`	`0x00000004`	`button`
`hs3001`	`0x00000044`	`hs3001`
`iaq`	`0x00000032`	`zmod4xxx`
`oaq`	`0x00000033`	`zmod4xxx`
`barometer`	`0x00000063`	`icp_101xx`
`icm`	`0x00000068`	`icm20948`
`magnetometer`	`0x0000000c`	`ak09916`
`sysc_oscsf`	`0x4001e03c`	`pythonperipheral`
`gpt`	`0x40169000`	`renesasra_gpt`
`agt0`	`0x400e8000`	`renesasra_agt`
`agt1`	`0x400e8100`	`renesasra_agt`
`agt2`	`0x400e8200`	`renesasra_agt`
`agt3`	`0x400e8300`	`renesasra_agt`
`agt4`	`0x400e8400`	`renesasra_agt`
`agt5`	`0x400e8500`	`renesasra_agt`
`sci0`	`0x40118000`	`renesasra6m5_sci`
`sci1`	`0x40118100`	`renesasra6m5_sci`
`sci2`	`0x40118200`	`renesasra6m5_sci`
`sci3`	`0x40118300`	`renesasra6m5_sci`
`sci4`	`0x40118400`	`renesasra6m5_sci`
`sci5`	`0x40118500`	`renesasra6m5_sci`
`sci6`	`0x40118600`	`renesasra6m5_sci`
`sci7`	`0x40118700`	`renesasra6m5_sci`
`sci8`	`0x40118800`	`renesasra6m5_sci`
`sci9`	`0x40118900`	`renesasra6m5_sci`
`portMisc`	`0x40080d00`	`renesasra_gpiomisc`
`iic0`	`0x4009f000`	`stub`
`iic1`	`0x4009f100`	`stub`
`iic2`	`0x4009f200`	`stub`

Total Peripherals: 32