Validation Report: sam4s16c
Architecture: ARMv7E-M.
1. Dynamic Simulation Validation
Status: ✅ Passed (simulation-ok)
[2m2026-10-18T14:40:22.084717Z[0m [32m INFO[0m [2mlabwired_cli::commands::run[0m[2m:[0m Starting LabWired Simulator
[2m2026-10-18T14:40:22.088632Z[0m [32m INFO[0m [2mlabwired_core::system::builder[0m[2m:[0m Loading chip descriptor: ../../chips/onboarding/sam4s16c.yaml
[2m2026-10-18T14:40:22.098274Z[0m [33m WARN[0m [2mlabwired_core::bus::profiles[0m[2m:[0m GPIO type 'sam4s_pio' (peripheral 'pioA') has no dedicated register model; falling back to the STM32F1 placeholder layout. This is a known-incomplete onboarding model — set `config.profile` or add a real model for correct behaviour.
[2m2026-10-18T14:40:22.098386Z[0m [33m WARN[0m [2mlabwired_core::bus::profiles[0m[2m:[0m GPIO type 'sam4s_pio' (peripheral 'pioB') has no dedicated register model; falling back to the STM32F1 placeholder layout. This is a known-incomplete onboarding model — set `config.profile` or add a real model for correct behaviour.
[2m2026-10-18T14:40:22.098441Z[0m [33m WARN[0m [2mlabwired_core::bus::profiles[0m[2m:[0m GPIO type 'sam4s_pio' (peripheral 'pioC') has no dedicated register model; falling back to the STM32F1 placeholder layout. This is a known-incomplete onboarding model — set `config.profile` or add a real model for correct behaviour.
[2m2026-10-18T14:40:22.098616Z[0m [32m INFO[0m [2mlabwired_cli::commands::run[0m[2m:[0m Loading firmware: "/home/andrii/Projects/labwired-renode/core/tests/fixtures/uart-ok-thumbv7m.elf"
[2m2026-10-18T14:40:22.098739Z[0m [32m INFO[0m [2mlabwired_loader[0m[2m:[0m ELF Entry Point: 0x401
[2m2026-10-18T14:40:22.098783Z[0m [32m INFO[0m [2mlabwired_cli::commands::run[0m[2m:[0m Firmware Loaded Successfully!
[2m2026-10-18T14:40:22.098813Z[0m [32m INFO[0m [2mlabwired_cli::commands::run[0m[2m:[0m Entry Point: 0x401
[2m2026-10-18T14:40:22.099889Z[0m [32m INFO[0m [2mlabwired_cli::commands::run[0m[2m:[0m Starting Simulation (ARM Cortex-M)...
[2m2026-10-18T14:40:22.103050Z[0m [32m INFO[0m [2mlabwired_cli::commands::run[0m[2m:[0m Initial PC: 0x400, SP: 0x20020000
[2m2026-10-18T14:40:22.103143Z[0m [32m INFO[0m [2mlabwired_cli[0m[2m:[0m Running for 20000 steps...
[2m2026-10-18T14:40:22.114659Z[0m [32m INFO[0m [2mlabwired_cli[0m[2m:[0m Progress: 10000 steps, current IPS: 632503.03
[2m2026-10-18T14:40:22.127578Z[0m [32m INFO[0m [2mlabwired_cli::report[0m[2m:[0m Simulation loop finished.
[2m2026-10-18T14:40:22.127596Z[0m [32m INFO[0m [2mlabwired_cli::report[0m[2m:[0m Final PC: 0x466
[2m2026-10-18T14:40:22.127601Z[0m [32m INFO[0m [2mlabwired_cli::report[0m[2m:[0m Total Instructions: 19999
[2m2026-10-18T14:40:22.127606Z[0m [32m INFO[0m [2mlabwired_cli::report[0m[2m:[0m Total Cycles: 20002
[2m2026-10-18T14:40:22.127610Z[0m [32m INFO[0m [2mlabwired_cli::report[0m[2m:[0m Average IPS: 695233.72
Hardware Coverage Report
| Peripheral ID | Base Address | Type |
|---|---|---|
dwt |
0xe0001000 |
dwt |
sram_bb |
0x22000000 |
bitbanding |
tc0_1_2 |
0x40010000 |
sam_tc |
tc3_4_5 |
0x40014000 |
sam_tc |
usart0 |
0x40024000 |
sam_usart |
usart1 |
0x40028000 |
sam_usart |
adc |
0x40038000 |
stub |
dacc |
0x4003c000 |
stub |
PMC_SR |
0x400e0468 |
pythonperipheral |
uart0 |
0x400e0600 |
sam_usart |
uart1 |
0x400e0800 |
sam_usart |
eefc |
0x400e0a00 |
stub |
rstc |
0x400e1400 |
stub |
wdt |
0x400e1450 |
stub |
peripheral_bb |
0x42000000 |
bitbanding |
crc |
0x40044000 |
stub |
pioA |
0x400e0e00 |
sam4s_pio |
pioB |
0x400e1000 |
sam4s_pio |
pioC |
0x400e1200 |
sam4s_pio |
spi |
0x40008000 |
stub |
twi1 |
0x4001c000 |
stub |
twi0 |
0x40018000 |
stub |
Total Peripherals: 22